Jannah Theme License is not validated, Go to the theme options page to validate the license, You need a single license for each domain name.

The easiest way to fix a running toilet

Image of the article titled The Easiest Way to Fix a Running Toilet

Photo: New Africa ((((Shutterstock).

Oh, the toilet. It’s a very perfect invention and hasn’t been substantially renewed for about five centuries since its introduction. The flush toilet you are using today is basically the same design as the one introduced by Sir John Harrington At 16th Century — It depends on water supply and gravity and uses a surprisingly simple mechanism to magically wipe waste into septic tanks or sewers. LBut like anything else, It can turn our back on us.

At one end of the disaster scale, it can clog up and overflow, turning an average day into a nightmare awakening. On the other side of that scale, it can constantly start running. It may seem like a small problem that your toilet is endlessly filled with water, bA constantly running toilet will cost you Money — The water pumped into your home is not free.

Fortunately, fFixing a running toilet is actually very easy and usually you don’t need to call a plumber. hThere are some easy ways to stop a running toilet yourself..

HowOilet wOak

First, take a short-term intensive course on how the toilet works. Look at the wall behind the toilet. You should see a valve running a hose in the toilet tank. That is your water supply. If you think something needs to be replaced, you can drain the toilet, but in diagnostic mode, It is best to keep the water running, as you may need to refill the tank several times.

There are lots of different toilet designs out thereHowever, the basic elements of a working toilet are the same. Fill valves and tubes, floats, and flappers. The fill valve fills the tank with water and then shuts it off until the float reaches a certain level. Using the toilet handle or button, the flapper is lifted, the water is discharged into the bowl and flushed, and the entire process begins. Also.

Now that you have a basic idea of ​​what you’re looking at, there are four common reasons why the toilet doesn’t stop working, and you can easily fix each one.

Check flappers and chains

Perhaps the most common reason for toilets to run is flappers. This is a rubber or plastic part that fits the flush valve and prevents water from flowing into the bowl. If the flapper does not fit the valve properly, a small amount of water will always leak into the bowl and the tank will enter an endless refill loop. If the classic “jigle handle” technique actually works, this is probably the problem because of that jiggle. Basically reattach the flapper.

Take some stick and gently push down on the flapper. Does the toilet stop suddenly? Then you have your culprit. There are two ways to fix this.

  • Replace the flapper. Examine the flapper itself. Is it distorted and discolored? If it is warped, The flush valve will not be installed properly and will need to be replaced.They are You can buy a universal flapper that is cheap and can be used in any toilet.
  • Fix the length of the chain. The toilet handle lifts the flapper with a chain and slowly returns to its original position when the tank is full. If the chain is too short, you can prevent the flapper from falling completely and sealing the flush valve. If it is too long, it can get caught under the edges of the flapper and have the same result. Cutting a long chain with pliers or replacing the chain with a slightly longer one often solves the problem.

Check the float

If the flapper looks good and looks fine, then check the float.. A float is a large plastic cylinder or sphere that literally floats in the water in the tank. As the water drops, the float will flow with it, opening the filling valve to allow more water to flow into the tank. When it floats and returns to its original position, the valve closes and the water stops.

If the float setting is too high, the tank will fill up and water will spill into the overflow tube (which is there to prevent the tank from overflowing). As the water continues to spill into the overflow tube, the float will not be high enough to block the inflow and a terrifying cycle of endless flowing water will begin.

The float is adjustable. There are usually simple screws that can be turned to change the height of the float. Look inside the tank. Perhaps there is a mark etched there to indicate the filling level, where the water level is set after the filling cycle. Next, check the filling valve in the tank. “Critical level” is marked.The water level should be about 1 inch under This mark is on whatever is etched on the tank (because different toilet kits are attached in different ways). Adjust the float until the water level is replenished to that point and see if that solves the problem.

Check the fill tube

Finally, look at the filling valve, which is a tube that extends from the water connection connected to the float. There is a short plastic tube that extends from the filling valve just above the overflow tube. When you wash the toilet, water flows through this tube into the overflow and fills the bowl. If not placed correctly, the bowl will not get enough water and the toilet may be up and running at all times.

If it comes off completely, reattach it and make sure it is firmly seated. Also, make sure that the end of the tube is located above (and in some cases directly) the overflow tube. Rinse the toilet and make sure all the water from the fill tube is in the overflow tube. This should solve the problems caused by this wonderful toilet technique.

If none of these fixes work, the next step is to replace the internal mechanics of the toilet (if you don’t know what’s there, you can buy it. Universal Repair Kit) Or call a plumber.

The easiest way to fix a running toilet

Source link The easiest way to fix a running toilet

Related Articles

Back to top button